搜索资源列表
stc12 eeprom
- 本演示程序在STC-ISP Ver 3.0A.PCB 的下载编程工具上测试通过,EEPROM 的数据 在P1 口上显示, 如果要在程序中使用或在文章中引用该程序,请在程序中或文章中
STC12c5A60s2.rar
- 次程序为最新STC的12系列的单片的A/D转换的C程序，一般提供为汇编程序，这个C程序可以通过串口观察得到,Sub-program for the latest STC' s 12 series of single-chip A/D conversion of the C program, are generally provided for the assembler, the C program can be observed through the serial port
wenduxuexiban
- 基于STC/AT89 C/S51的单点温度检测 DS18B20 可控制上下限温度-STC/AT89 C/S51 based on the detection of single-point temperature can be controlled DS18B20 the upper and lower limits of temperature
AD
- 利用STC12C5410AD单片机自带的AD和用7219显示，所编写的C程序-STC series single-chip microcomputer to download the latest software stc-isp-v4.80-not-setup
STC_4_DA_test
- STC 4路DA输出测试 内部PCA控制PWM，C语言代码-STC 4 way DA output test internal PCA control PWM, C language code
16X16-2
- 16X16点阵显示汉字 使用 【STC12C5A60S2（STC公司的一种51单片机）】，晶振频率为22.1184MHz-16X16 dot matrix display Chinese characters using 【STC12C5A60S2 (STC' s a 51 MCU)】, crystal frequency of 22.1184MHz
Alamouti-STC
- 这个是老师给的关于stc的cpp文件。希望对有需要的人有帮助。-this is a c++ file which is given by my professor.hope it is useful to you.
DDD112_DRV1
- USB接口芯片D12在STC单片机SCM上的驱动driver开发，定义ENDPOINT0，ENDPOINT1与ENDPOOINT2为管理通道、中断模式与批模式。压缩包中包含头文件与C文件，在keil C8.2下编译使用，，hex文件约7KB。 -The USB interface chip D12 STC SCM SCM driven driver development, the definition ENDPOINT0, ENDPOINT1 and the ENDPOOINT2 mana
stc-isp-v3.94-setup
- 一个 用来把写好的c++文件烧写到 单片机中的应用软件 适用性很好 可广泛用于 单片机开发 舞蹈机器人等的软件开发当中-One to which written c++ file programmed into the microcontroller applications applicability good microcontroller development Dancing Robot can be widely used in software development
hkt-stc
- 用C编写的单片机与对讲机之间的通信功能的程序，两者之间可以互相说话接听-The communication between the single-chip transceiver written in C program between the two can talk to each other to answer
HMC5883 STC IIC测试程序.C
- HMC5883 STC IIC测试程序，适合STC89C系列，很方便的程序，用来驱动3轴数字罗盘IC
LED
- 单片机C语言，单片机是STC的8051单片机，实现小灯闪烁延时程序-Singlechip C language, single-chip microcontroller 8051 STC, achieve a small delay procedure
MODBUS
- C语言写的 STC单片机的MODBUS RTU程序，实现了 03 读单寄存器和多寄存器。06写单寄存器功能.-C language to write the STC MCU MODBUS RTU procedures, to achieve the 03 read a single register and register. 06 write a single register function.
AD
- 利用C编写的基于STC的内部AD的LCD1602程序-use c write the programe
1111
- 串口通信，上位机软件,stc单片机做串口开发时，很有用的参考资料，C#版-Serial communication, PC software, stc microcontroller serial do when developing, very useful reference material, C# Edition
STC EEPROM
- STC 单片机 读取 EEprom C语言代码(STC microcontroller to read the internal EEprom C language code)
C
- ＳＴＣ程序以中断的方法查询，供编程初学都学习。(STC program to interrupt the query, for beginners to learn programming.)
stc-isp-15xx-v6.85p
- 在此行自己on公交卡vknkvh显示hello(hellojdkfjfkhkfjzgjcgfjsgfkgsfjk)
end
- 通过串口通信实现RC522对 M1卡的读写操作(Realization of RC522's reading and writing to M1 card through serial communication)