搜索资源列表
AVR2
- AVR单片机定时器1中断程序每500MS将PB0端口的二极管点亮一次，程序运行在内部1M晶振下-Program the AVR timer 1 interrupt every 500MS will PB0 port LED lights once, run under the internal crystal 1M
swtich-control-LED
- swtich语句的控制P0口8位LED的点亮状态-swtich sentence control P0 mouth 8 LED lightens the condition
right-lateral--running
- 右移运算流水点亮P1口8位LED，新手值得一看的入门小程序.-The right lateral operation running water lightens P1 mouth 8 LED
lsd
- 按键控制LED流水灯；按键1按下前8个灯从左到右依次点亮，按键2按下中间前8个灯从左到右依次点亮，按键3按下所有灯全亮-Water control button LED lights sequentially lit buttons the eight lights left to right 1 Press button 2 press from left to right is lit in the middle eight lights, key 3 Press All full bri
LED
- 点亮一个LED灯,本程序是通过C语言编程的，属于比较简单-Light a LED light, the C programming language, are relatively simple
LED_4key
- /****************************************************** 程序功能：用中断方式读取四个独立式按键的键值，同时用 D1~D4四个LED的点亮来指示k1~K4四个按键的按下 ---------------------------------------------------- 测试说明：按动K1~k4四个按键，观察LED是否正确点亮 *********************************************
74HC595_single_led
- 实现74HC595控制24个led。依次点亮，和同时点亮-74HC595 control 24 LEDs. Were lit, and lit at the same time
1.1
- 点亮LED灯 循环点亮使用单片机P0.1~0.7-Lit LED lights light cycle MCU P0.1 to 0.7
Stm32-lights-led-lights
- 用stm32点亮led灯,功能正常，所用IAR开发环境编程-Stm32 lights led lights
led
- 这是一个有关点亮一盏灯的程序，非常适用于刚学单片机的同学-This is a program lit a lamp, ideal for students just learning microcontroller
LED
- 这是一个点亮LED的程序，源代码欢迎下载-This procedure is a LED light
work_2
- 1、将51单片机片内数据存储器30H单元～3FH单元的数据清零，如果成功，点亮EZ-51开发板上的某个LED。 2、将51单片机片内数据存储器30H单元～3FH单元的内容复制到50H单元～5FH单元，如果成功，点亮EZ-51开发板上的某个LED。 3、将51单片机外部数据存储器1000H单元至1FFFH单元数据清零。该任务无法通过EZ-51开发板验证，可以通过Keil C的仿真调试验证。 4、将51单片机外部数据存储器1000H单元至1100H单元的数据复制到2000H单元至2100
liushuideng
- 流水灯代码，LED灯按四种模式点亮熄灭,第一种亮灯左移点亮，第二种一灯右移点亮-Light water code, LED lamp lights extinguished by four modes
led2
- led跑马灯，用循环法依次点亮led灯，每次亮一盏灯-Led entertaining diversions, by using the circulation method in turn light led lights, light a lamp at a time
Function-realization
- 第一个是通过51单片机实现音乐五线谱编程。第二个是利用流水灯点亮LED灯。第三个是利用数码管反复显示数字。-The first is to achieve a musical staff by 51 microcontroller programming. The second is the use of the LED lamp lighting water. The third is the use of digital display numbers repeatedly.
C51
- 这是单片机代码 用于接受按钮信号 并点亮制定的led等-This is the microcontroller code used to accept the button signal and light up the development of the led and so on