搜索资源列表
aaa
- 本文介绍了两相四拍混合式步进电机的工作原理及其磁网络模型，推 导了步进电机的动态方程。分析了两种细分驱动方法:等电流法和电流 矢量法恒幅均匀旋转法，提出了基于单片机控制的PWM电流矢量恒幅 均匀旋转的细分驱动技术，实现了步进电机32细分驱动。-so much,so nice.
aaa
- 在数控原代码开发过程中提出了步进电机正反转控制的实现方法,并根据此方法,给出了其相应的实现程序。 -very good.
s3c2410
- s3c2410 步进电机的驱动 （毕业设计）-s3c2410 stepper motor drive (graduation project)
S3C2440_pwm
- S3C2440的PWM输出驱动,可以输出频率可调的PWM方波以控制步进电机-The S3C2440 PWM output drive, the PWM square wave can be output frequency is adjustable to control the stepper motor
STEPMOTOR_L298DRVtest
- 用于L298N的交流电机驱动，本代码用于步进电机正传两相八拍的程序。-For L298N AC motor drive, the code for stepper motor True Story of two-phase eight-beat program.
STEPMOTOR_L298DRVtest
- 用于L298N驱动步进电机，本代码用于步进电机反转两相四拍。-For L298N drive stepper motor, and the code for two-phase stepper motor reversal shot.
STEPMOTOR_L298DRVtest
- 用于L298N驱动控制步进电机，本代码是其中的两项四拍程序。-For L298N drive control stepper motor, the code is one of the two four-beat program.
motor2.0
- 基于linux rethad gec2440（ARM9）板卡开发的步进电机驱动，可以控释电机正反转，停止。-Based linux rethad gec2440 (ARM9) stepper motor driver board development, controlled-release motor reversing, stop.
rightMotorContr.c
- MicroMouse618上的右步进电机驱动时序优化程序，2013版本-On the right MicroMouse618 stepper motor driver timing optimization program, 2013 version
lpl_stepper
- linux下基于S3C2440开发的步进电机驱动，一根信号线控制HB202M细分器即可实现步进电机速度和方向的控制-linux based S3C2440 development of stepper motor drive, a signal line control HB202M subdivision stepper motor controller can achieve the control of speed and direction
drivate
- 这是2410控制步进电机的驱动程序，仅供参考。-This is the driver it is trying to control a stepper motor
STEP-MOTOR
- 在Linux系统下步进电机控制程序，通过中断控制器实现按键控制-In the Linux system stepper motor control procedures to achieve controlled by the interrupt controller buttons
stm32
- 用STM32做为主控制芯片，步进电机的控制程序-Mainly to do with the STM32 chip control, stepper motor control program
stepermoto
- 供测试使用的四项五线步进电机的c语言驱动程序，使步进电机旋转两圈。-C language for test using four five wire stepper motor driver, the stepping motor rotates two circles.
Motor_control
- 供测试使用的二相步进电机驱动程序（胶水）-Phase step for testing the use of stepper motor driver
Gcode_executer
- 供测试使用的G代码执行程序，供二相步进电机。-For testing the use of G code program execution, for two-phase stepper motor
Bipolar_Stepper_Motor_Class
- 供测试使用的二相步进电机驱动程序，配合g代码的使用。-Phase step for testing the use of stepper motor driver, and with the use of G code.
motor_210
- 粤嵌210步进电机驱动，内有详细注释,供参考-Guangdong inlay 210 stepper motor driver, there are detailed notes
stepper-motor-driver
- L6208步进电机驱动，可以正转动，反转，PWM更改速度控制，-L6208 stepper motor driver, you can now rotate, reverse, PWM speed control change
S3C44B0X-STEPMOTOR
- 一个S3C44B0X控制步进电机的例子，其中涉及怎样操作相关寄存器和怎样赋值是电机转动，是进行ARM控制步进电机开发的很好的基本性的参考-An example S3C44B0X stepper motor control, which involves how to operate and how to assign the relevant registers motor rotation is performed ARM controlled stepper motor developed