搜索资源列表
8051的UDP协议实现 协议实现--c语言编写
- 8051的UDP协议实现 协议实现--c语言编写 用51单片机实现的。-8051 to achieve the UDP protocol -- c language with the MCS-51 microcontroller.
SPCE061A_TCPIP
- 以凌阳单片机SPCE061A为核心的TCPIP协议实现（C原代码）。-to Sunplus SCM SPCE061A TCPIP as the core protocol (C source code).
dummy I2C bus
- 这是一个模拟I2C通信协议的C语言模块，可以在基于51系列单片机的C语言程序中进行调用，调用方式我在模块中已经添家了详细的说明，请自己查阅！-This is a simulation I2C communication protocol C language module, Based on the 51 Series MCU C language program which calls, Call module way I have Tim home detailed descr iption
TCPIP-C
- 网络,基于嵌入式的网络协议,UDP/IP的协议.处理器无关部分源代码--UDP/IP network protocol in embedded enviroment.
DS18B20驱动程序(C语言)
- 功能：实现对DS18B20的读取 原理：单总线协议 注意：单总线协议对延时要求比较严格，此程序中采用的是11.0592M的晶振，如果使用其他的晶振请跟据DS18B20的资料修改延时参数-functions : to achieve DS18B20 read Principle : single-bus protocol attention : single-bus protocol to delay requirements more stringent, this procedure is u
单片机实现TCP IP协议的完整C源程序
- 转载单片机实现TCP/IP协议的完整C源程序，带程序注解的，供大家研究-reproduced MCU TCP / IP protocol complete C source code, annotated with procedures for everyone to consider! !
FM24CL64驱动C语言程序，试用于IIC协议
- FM24CL64驱动C语言程序，试用于IIC协议,FM24CL64 drive C Language Program, the trial protocol in the IIC
DVP-protocol.rar
- 台达PLC通讯协议，已经C语言的实现－基于S3C44B0的开发,Delta PLC communication protocol, has been the realization of C language- based on the development of S3C44B0
Converter_C51.rar
- LED控制，通过DMX512协议接收并调光,LED control, receive DMX512 protocol then dimming
modbus.rar
- modbus485通信协议C程序，经修改已用于项目，熟悉后修改部分参数即可用于485通信相关项目。,modbus485 communication protocol C program, as amended, have been used for the project are familiar with some parameters after the change can be used for 485 telecommunications related projects.
BMP085
- BMP085气压传感器在单片机STC89C5的测试程序，使用 IIC协议。由1602显示。-The BMP085 pressure sensor the microcontroller STC89C5 the test procedure, the use of the IIC protocol. From the 1602 show.
Dimmer_PICC
- 基于PIC单片机，DMX512协议的LED控制器程序，包含多种花样转换、I2C操作、串口通信等-Based on PIC microcontrollers, DMX512 protocol LED controller program includes a variety of pattern conversion, I2C operation, serial port communication
STM32-CAN
- 基于STM32 处理器的CAN总线通信协议源代码-Based on the STM32 processor CAN bus communication protocol source code
modbus-51-src
- 汇编，C 源码 用STC89C58单片机做的数据采集和控制，12位AD转换使用TLC2543，通讯协议采用MODBUS（RTU），通过拨码开关改变从机地址，支持模拟量或数字量的读写。（4路模拟量输入、6路开关量输出（继电器输出）、8路开关量输入）开发环境:KEIK 7.06 (2006-7-5，C-C++,61KB,17次) -Microcontroller to do with STC89C58 data acquisition and control, use 12-bit AD
PPPCcode
- PPP协议C语言源程序，做gprsDTU的必看！-PPP protocol C language source code, make gprsDTU the must-see!
BSL
- 用于sst89x516(sst89x564)的Bootloader,使用超级终端用xmodem协议下载,(只支持bin文件的下载).在晶振为11.0592,未开双倍速的情况下,波特率为57600bps.在超级终端中长按 Z 键并对系统上电进入下载,否则500ms后跳转至block0中程序执行,可代替原SST中的BSL.可扩展实现远程升级-For sst89x516 (sst89x564) the Bootloader, use HyperTerminal to download using xm
CiACanOpen
- 从官方网站获得的CanOpen通讯协议的全部资料，已经按照内容更改文件名，这是最全的协议了-Obtained from the official website of the All CanOpen communications protocol has been changed in accordance with the contents of the file name, which is most of the protocol
MODBUS-C-program-on-51MCU
- 在51单片机上实现工业ModBus通讯协议，RTU协议。包括主机的C程序和从机的C程序。可在PROTEUS仿真软件上运行通过。提供仿真原理图。-Industrial ModBus protocol on 51 single, RTU protocol. C program includes a host and slave C program. PROTEUS simulation software can be run on the pass. Provide simulation schem
MODBUS-RTU-C-code-8051
- RS485通讯与MODBUS协议（C代码8051）-RS485 communication with MODBUS protocol (C code 8051)
Ymodem
- 从STM官方例程中提取的Ymodem协议的C实现，亲测可用，可以与Windows超级终端互传文件。可以应用于32位或8位单片机，很实用的东东。(From the STM official routine extracted from the Ymodem protocol C implementation, pro test available, you can share files with the Windows super terminal. Can be applied to 32 b