搜索资源列表
c51_Code_Packet
- 这是单片机C51的各种代码包，包括：I2C应用程序、滚动码应用原程序、红外应用源程序集、用计算机并口模拟SPI通讯的C源程序-C51 microcontroller This is the code, including : I2C applications, rolling code original application procedures, Application of infrared source sets, computer simulation of SPI communica
DSPLOAD1_0
- Anlog 公司的DSP,ADSP-BF531并口模拟spi引导程序,是采用BF531从引导模式。-Anlog company's DSP, ADSP-BF531 Parallel simulation spi guide procedures, BF531 is the model from the guide.
spi-code
- 用计算机并口模拟SPI通讯的C源程序，验证可用--C program to simulate SPI communication by parallel port.
lcd
- 12864类型lcd驱动（arm7），其中包含串行，并行，gpio实现，spi实现，urat实现，1138开发板，lpc2000系列开发板lpc2103，lpc2131，lpc2132），均已调试通过。-12864 Type lcd driver (arm7), which includes serial, parallel, gpio achieve, spi implementation, urat achieved 1138 development board, lpc2000 devel
spiflash
- spiflash utility and schematics for diy parallel port programmer to program newer motherboards with spi flash
spi
- 三线spi接口，用verilog实现，作为一个模块，可以接收并行数据，然后串行发送-Three Line spi interface, using Verilog implementation, as a module, can receive parallel data, and then send the serial
cycle_time
- *51单片机时序总驱动 *包括并口的6800和8080,串口的I2C,SPI,1-WIRE *所有片选由上层驱动完成(I2C,1-wire为总线选择)-* 51 single-chip timing drive* The total includes the 6800 and 8080 parallel port, serial I2C, SPI ,1-WIRE* All films selected from the top drive to complete (I2C ,1-wire
MCP2515_driver_s3c2440based
- 本驱动程序在s3c2440上实现了两路基于SPI的CAN总线控制器。两通道可以并行，并使用外部定义的两个信号量来通知接收任务收到CAN总线帧，并将其存入预先定义的队列中（帧定义在CAN总线控制器驱动程序的头文件中）。CAN总线控制器的中断引脚分别连接到ARM的EINT3和EINT8_23上-The driver s3c2440 achieved a two-way SPI-based CAN bus controller. Two channels can be parallel, and us
SPI
- 通过并口实验，进一步熟悉了同步通讯原理，也对此单片机有了进一步的了解。-Through the parallel experiment, more familiar principle of synchronous communication, but also have a better understanding of this microcontroller.
PC_SPI
- 通过计算机25针并口读写SPI总线Flash存储器-25-pin through the computer parallel port read and write SPI bus Flash memory
c8051lcd1602a
- c8051,1602A LCD显示程序,运行程序LCD显示"BT F310 V1.0",SPI接口方式的NLSF595并行输出 控制LCD-c8051, 1602A LCD display program, run the program LCD display " BT F310 V1.0" , SPI parallel interface mode of NLSF595 LCD output control
SPIsend
- STM32F103 Arm 单片机的 SPI 实现数据从并行到串行的收发-STM32F103 Arm Microcontroller SPI data from parallel to serial transceiver
Flash_Ctrl
- 串行flash的写及擦除操作，串行flash，spi接口，支持并口输出-Serial flash write and erase operations, serial flash, spi interface, support for parallel port output
lcd
- 1602A LCD显示程序,运行程序LCD显示"BT F310 V1.0",SPI接口方式的NLSF595并行输出 控制LCD-1602A LCD display program, run the program LCD display " BT F310 V1.0" , SPI parallel interface mode of NLSF595 LCD output control
MSP430PAD9854-Parallel
- MSP430通过并行、端口模拟SPI方式控制AD9854 程序 资料包括 MSP430F149通过口线模拟SPI时序控制AD9854扫频程序。 MSP430F149通过并行总线控制AD9854扫频程序。 整理时间： 2011_12_26 沨-MSP430 control the AD9854 via the parallel port analog SPI In
spi-code
- 用计算机并口模拟SPI通讯的C源程序，验证可用--C program to simulate SPI communication by parallel port.
LAB8_LCD_driver
- 使用STC12L之8051驅動ILI9325之TFT驅動IC, 傳輸界面可用SPI/並列8B/並列16B等模式, 並可完成LCD豎屏橫屏的效果展示!-Use 8051 STC12L of driving TFT driver IC, the available transmission interface ILI9325 SPI/Parallel 8B/16B and other parallel mode, and complete the effect LCD horizontal scre
spi
- 用于SPI串口和并口以及并口和串口的转换(Serial and parallel conversion)
STM32驱动ch395_4个socket连接
- main.c已详尽注释连接的引脚 和 调试助手参数。STM32分别以串口,硬件SPI,模拟并口驱动CH395,4个socket连接, 原路返回上位机发送的数据。串口模式支持更改工作波特率，硬件SPI速率最高36MHz, 模拟并口较快，这三种模式支持在stm32任意型号下。(Main.c has commented on pins and debugging assistant parameters in detail. STM32 drives CH395 and 4 sockets by se
spi_slave
- 使用VHDL语言写的程序，利用SPI协议实现串并转换电路(Programs written in VHDL language and series-to-parallel conversion circuit implemented by SPI protocol)