搜索资源列表
ctrl_PWM
- 舵机控制源程序，属于单舵机控制，PCI总线实现。-Steering gear control source, belonging to a single steering control, PCI bus.
onePWM
- 发个智能车的舵机控制的例子。代码实现的功能是使小车自动左右拐弯-Made a smart car steering gear control example. Code to achieve the function is to enable automatic car turning around
pwm_50hz
- fpga控制舵机s3010旋转，VHDL编写,通过按钮控制-fpga control of steering rotation, VHDL preparation
pwm
- 利用Verilog语言产生17路PWM波，控制17路舵机，可以作为IP核添加到AVALON总线上，在nios IDE里用C语言控制。-Using Verilog language production of 17 Road PWM signal to control 17 Servos, can be used as IP core to the AVALON bus, in the nios IDE in control with the C language.
PWMkongzhi
- 用PWM控制舵机，LED灯显示，舵机连续打角-PWM-controlled steering, LED light display
Servo-using-the-program
- 本文是用AVR atmega8语言写的一个控制舵机的例子，用单片机脉冲PWM信号控制舵机角度，抖动小。-This article is written in the language with AVR atmega8 example of a servo control, PWM signal with a single-chip pulse control steering angle jitter.
servo_PWM
- 舵机控制程序，采用VHDL编写，测试成功可同时控制多个舵机-Servo control procedures, the use of VHDL to write, test can simultaneously control multiple servo success
PWM
- MC9S12XS128 PWM介绍，实例程序，使用说明，舵机控制程序，代码-MC9S12XS128 PWM introduction, examples of procedures, instructions, steering gear control program, code
duoji_pwm
- 一个控制舵机的简单程序，测试过能用，实现也方便-A simple program to control the servo, tested can also facilitate
duoji
- 基于FPGA的，运用Verilog语言编写的，通过黑线检测来控制舵机的程序。-FPGA-based, using Verilog language, through the detection of black lines to control the steering process.
FPGA_BasicProgram
- 本人收集大部分FPGA的基础参考例程，包括各种接口技术如I2C,RS232,UART,SPI，PS/2等，还有驱动各种LCD如1602，NOKIA5110,FPGA超声波测距，FPGA控制ADS7825,ADS7844,ADS2807,THS1206,TLC2543,TLC5510A,MAX1312等，FPGA控制舵机，步进电机，niosii。-I collected most of the FPGA-based reference routines, including a variety o
servo
- Verilog编写的辉盛9g舵机控制程序，clk：25MHz，输入角度（0~180），输出PWM，直接连到舵机引脚上即可使用-Verilog prepared Fraser 9g servo control procedures, clk: 25MHz, input angle (0 to 180), the output PWM, directly connected to the steering pin can be used
FPGA-auto-car-and-arm
- VHDL Verilog编写，实现无线串口通信遥控4自由度机械臂和车身行动驱动。串口命令格式和舵机参数可根据实际需要自行调整-Verilog VHDL prepared to achieve a wireless serial communication remote control 4 degrees of freedom manipulator and body action. Serial command format and actuator parameters can be adju
pwm
- 通过该IP核输出三路pwm波，可用来控制一个舵机和两块L298N驱动板，从而控制电机。-IP core output by the three-way pwm wave can be used to control a servo drive plate and two L298N to control the motor.
pwm_generate_module
- verilog编写的，用按键控制PWM波占空比。可以定义死区，用来控制舵机或者led灯的亮暗。-Verilog prepared, with the button to control the PWM wave duty cycle. You can define the dead zone, used to control the steering gear or led lights bright and dark.