搜索资源列表
8-light
- 一个简单的8路彩灯，简单实用，是初学者学习vhdl，的很好的参考。-a simple 8 Lantern Road, simple and practical, is learning vhdl beginners, a good reference.
自制串口8路光隔DO
- 自制的串口控制8路光藕隔离输出，可以通过计算机串口控制，8路输出-homemade serial control a variety of eight-channel optical output isolation can be controlled via computer serial port, eight output
8路视频光端机的VHDL源码
- 8路视频光端机的VHDL源码
将C8051F040单片机的8路A/D及片内温度传感器的采样值通过串口发送到上位机上
- 将C8051F040单片机的8路A/D及片内温度传感器的采样值通过串口发送到上位机上,C8051F040 MCU to 8-channel A/D and the temperature sensor chip through the serial port of the sample value is sent to the host computer on
modbus-51-src
- 汇编，C 源码 用STC89C58单片机做的数据采集和控制，12位AD转换使用TLC2543，通讯协议采用MODBUS（RTU），通过拨码开关改变从机地址，支持模拟量或数字量的读写。（4路模拟量输入、6路开关量输出（继电器输出）、8路开关量输入）开发环境:KEIK 7.06 (2006-7-5，C-C++,61KB,17次) -Microcontroller to do with STC89C58 data acquisition and control, use 12-bit AD
C
- 8AT89C52,ADC0809 8路数字电压表测量由A/D转换、数据处理及显示控制等组成，测量0～5V范围内的8路输入电压值，由4位共阳LED数码管轮流显示，最大分辨率0.01V，误差±0.02V。-8AT89C52, ADC0809 8 way digital voltage meter measured by A/D conversion, data processing and display control of the measurement range of 0 ~ 5V inpu
8AD
- ad转换，8路温度自动测量，可以设置温度上下限，并能实现控制-ad conversion, 8-way automatic temperature measurement, you can set the temperature of upper and lower limits, and to achieve control of
qiangdaqi_8
- 基于单片机的8路竞赛抢答器，包括源程序和Proteus仿真电路图，欢迎下载。-Based on SCM and road race vies to answer first, including the source program and Proteus simulation diagram, welcome to download.
protelDesignDocument
- 8路温度巡回检测系统设计 温度检测范围0~100℃，分辨率0.5℃，环境共模噪声为5V。 各路可设置温度的上限值和下限值，在超出范围时发出报警信号。 每秒钟至少检测一次。 显示器轮流显示实时检测结果。-8 Temperature Cycle Detection System Temperature Measuring range 0 ~ 100 ℃, resolution of 0.5 ℃, environment, common mode noise 5V. Separ
8_Lantern_controller_design_report
- 8路彩灯控制器设计报告:设计方案详细，内容规范，自己的课设哦-8 Lantern controller design report: detailed design, content specification, design their own lesson Oh
8路PT100温度巡检仪
- 利用AT89C52单片机制作的8路PT100温度巡检仪
8路AD采集
- AD转换8路切换汇编程序，可以实现数据的采集，进行通道的选择。
0625、8路抢答器
- 用汇编语言和c语言实现8路抢答器功能，包含仿真图和源程序，以上内容仅供学习交流使用，若用于商业用途作者将追究责任。(Using assembly language and C language to achieve 8 way responder function, including simulation and source code, the above content is only for learning, exchange, use, if for commercial use,
XL
- 实时采集8路AD通道模拟量信息,定时发送采集回来的模拟量信息, 控制PORTC0端口输出高低电平.(Real time acquisition of 8 channel AD analog information, send back the analog information periodically, control the output level of the PORTC0 por)
8路红外遥控
- 8路红外遥控(8 way infrared remote control)
W5500模块－8路服务端模式-STM32例程(中断)
- W5500模块－8路服务端模式-STM32例程(中断)(The W5500 module 8 road service mode -STM32 (interrupt routines))
单片机AD0808LCD
- 单片机8路AD0808转换加LCD显示源代码和仿真程序,是C语言写的,仿真是proteus软件的.(SCM 8 AD0808 conversion plus LCD display source code and simulation program, is written in C language, simulation is Proteus Software)
8路抢答器
- 抢答器电路设计，实现8路抢答，内有设计电路图及PCB板，有文档详细说明(Buzzer circuit design and realize 8-way vies to answer first, inside the circuit diagram and PCB design, there are detailed document)
8路捕获程序
- 利用单片机实现的多路超声波的捕获，对初学单片机有很大的价值(Capture multiple ultrasonic)
8路PWN
- 用两个定时器TIM2和TIM4输出8路的PWM(Output 8-channel PWM with two timers)