搜索资源列表
已知两点求第三点的双字节无符号定点插值算法
- 两个点的线性插值定点数算法 说明：1、基本公式 y=( y2-y1 ) ( x-x1 ) / ( x2-x1 ) + y1 2、根据直线斜率的正负、内插外插的不同，分为6种情况。 3.参见文件夹中的“插值算法的6种情况”一图。-two points of linear interpolation algorithm for determining points : one, the basic formula y = (y2 - y1) (x-x) / (x2 - x1) y1 2,
aduc7000_pwm
- This project is created using the Keil ARM CA Compiler. The Logic Analyzer built into the simulator may be used to monitor and display any variable or peripheral I/O register. It is already configured to show the PWM output signal on PORT3.0 an
adu812_eeprom
- This example demonstrates how to erase, write, and read the on-chip 640-byte EEPROM Data Memory of the Analog Devices ADuC812, ADuC814, ADuC816, and ADuC824 devivces. This example includes a µ Vision2 Project with a target for each supported dev
msp430mpsoft
- * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS AND ANY EXPRESS * OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SH
s3c44b0chumoping
- 当手指或笔触摸屏幕时，平常相互绝缘的两层导电层就在触摸 点位置有了一个接触，因其中一面导电层接通X轴方向的5V均匀电压场(图a) ，使得检测层的电压由零变为非零，控制器侦测到这个接通后，进行A/D转换 ，并将得到的电压值与5V相比即可得触摸点的X轴坐标为（原点在靠近接地点 的那端）：Xi=Lx＊Vi / V（即分压原理）同理得出Y轴的坐标，这就是所有电 阻技术触摸屏共同的最基本原理。-finger or pen to touch the screen, usually two
STR71x_GPIO_Scanning_a_44Matrix_Keypad
- The aim of this application note is to show to scan the 4x4 matrix keypad multiplexed with a four 7-segment display. The software attached to this application note scans the pressed key and displays it on the multiplexed 7- segment LEDs. Thi
01_GettingStarted
- This getting started exercise will guide you through the step-by-step process of transforming a MATLAB floating-point model into a hardware module that can be implemented in silicon (FPGA or ASIC). The design is a general purpose FIR filter taken fro
05_UsingAccelWare
- This lab exercise will introduce you to the AccelWare IP generators. AccelWare is a library of over fifty IP generators, available in the form of three toolkits that produce synthesizable MATLAB for common MATLAB built in and toolbox functions. Each
IMAG_c
- CCS编程环境 使用的是汇编加C的混合编程方法： The programme of the Correlation Algorithm. Using INT2 to get the input signal. Array x, in first step, is the input signal produced by programme, in next step, is the input signal get from A/D, the length is 128, 3
oscilloscope
- 单片机通过DA对信号采样，然后在液晶显示波形。 功能：采集数据、存储并Y路输出。扩展：A,B路选通，单次/连续触发方式切换， 锁存当前波形，垂直方向增益，垂直方向移动波形-microcontroller through DA sampling of the signal, then the LCD wave. Functions : data collection, storage and Y output. Expansion : A, B channel switching, singl
4.5_rtc_test
- Embest S3C44B0X Evaluation Board RTC Test Example RTC Check(Y/N)? y Set Default Time at 2004-12-31 FRI 23:59:59 Set Alarm Time at 2005-01-01 00:00:01 ... RTC Alarm Interrupt O.K. ... Current Time is 2005-01-01 SAT 00:00:01
X-Y
- 通过插补计算实现在51单片机上控制X-Y机械手臂绘图的功能-Calculated through interpolation single-chip implementation of the 51 control XY robot mapping function
RGBtoYCbCr
- 采用FPGA实现色彩空间转换R’G’B’ to Y’CbCr的VHDL和verilog源代码,支持xilinx的各种器件. -FPGA realization of the use of color space conversion RGB to Y CbCr of VHDL and Verilog source code, to support a variety of Xilinx devices.
font_krs2
- ShCti driver user s manual, y Details NDIS driver development, Under XP-driven development (Engl Based on the expansion of passthr Parallel and Distributed Simulati The driver of a scanner to prepar Tuopu TCB8000 Chinese liquid cry
xapp930
- RGB to Y CB CR conversion source code in VHDL
keyboardcontroller_latest.tar
- 这是一个非常小而简单的模块，它通过一个键xy矩阵扫描，并产生一种“快照”的 位的代表在扫描采样的按键开关状态。 有在模块的内存，使输出保持不变的扫描过程中，并同步更新。 把钥匙是连续取样，但向上的按键开关存储器存储的所有数据，直到最后输出 “快照”的生产。 该模块是Verilog的参数，并与小矩阵式键盘推荐使用。据 在实际测试硬件。-This is a ve
MIPS1CYCLE
- MIPS single-cycle processor design in verilog.Instruction memory to the design and initialise it with your assembly code-a. Load the data stored in the X and Y locations of the data memory into the X and Y registers. b. Add the X and Y registers an
Point-x-y
- 先建立一个点类Point，包含数据成员x，y（坐标点）。以它为基类，派生出圆类Circle，增加数据成员radius（半径），再以Cirlcle类为直接基类，派生出圆柱体类Cylinder，再增加数据成员height（高）。要求： （1）每个类都有构造函数、用于从键盘获取数据的成员函数set()，用于显示数据的成员函数display()。 （2）用虚函数输出各类对象信息 -First establish a point class Point contains data member
contador-caso-especial-y-procedimientos
- contadores y ejemplos de diseñ o en verilog
sondbox-3.18.y.tar
- This patch for the sondox board. This board is rasperrypi based with addition of wm8737 codec and vs1063 ogg encoder. These patch are to be apply on top of raspberry rpi-3.18.y branch.-This is patch for the sondox board. This board is rasperrypi base