搜索资源列表
CC2500-DONGLE-RX-V40
- 这个是CC2500在em78p447的程序-the CC2500 is in the process em78p447
9E5-Rx
- 无线单片机nFR9E5的收发程序例子,供参考 -wireless transceiver examples of procedures for reference
Rx
- CC1100做呼叫器的程序(C语言)用8051与CC1100接口,语音压缩,频率在916.5MHZ
Infrared-RX
- 用单片机接收红外线IC发出的信号，汇编语言格式。
905
- NRF905驱动代码 // The content of this struct is nRF905 s initialize data. // CH_NO=1 433MHZ Normal Opration,No Retrans RX,TX Address is 4 Bytes // RX TX Payload Width is 32 Bytes Disable Extern Clock Fosc=16MHZ // 8 Bits CRC And enable
msp430x11x1_ta_uart9600_04
- Descr iption: This program demonstrates a half-duplex 9600-baud UART using // Timer_A3 using no XTAL and an external resistor for DCO ROSC. DCO used for // TACLK UART baud generation. The program will wait in LPM4, echoing back // a received ch
rx
- 这个程序是控制无线模块2401接受，为51系列单片机控制。可以将接收到的字节上传到电脑的串口
fet440_uart11_38400
- Echo a received character, RX ISR used. Normal mode is LPM0. // USART1 RX interrupt triggers TX Echo. // Baud rate divider with 1048576hz = 1048576/38400 = ~27.31 (01Bh|03h) // ACLK = LFXT1 = 32768Hz, MCLK = SMCLK = default DCO = 32 x ACLK = 10
rx
- 家电自动控制系统，定时开关，采用遥控器，按键操作，中文12864液晶示，-appliance control system, timing switches, using remote controls, buttons, LCD showed 12,864 Chinese,
f347 uart
- f347 uart tx/rx
CC1100_RF
- 这个是CC1100的通信程序，包含了所有的功能，WOR,CCA,RX TX等-This is the CC1100' s communication program, contains all the features, WOR, CCA, RX TX, etc.
ModbusMaster
- ModbusMaster.h - Arduino library for communicating with Modbus slaves over RS232/485 (via RTU protocol). This file is part of ModbusMaster. ModbusMaster is free software: you can redistribute it and/or modify it under the terms o
RF2411_avr(RF2401EK)
- 用NRF2401实现无线收发，与51单片机连接的时候，需要加电阻。-The nRF2401A can be programmed using a simple 3-wire interface where the data rate is decided by the speed of the micro controller. By allowing the digital part of the application to run at low speed while maximi
RX
- 红外线遥控灯,遥控灯的亮灭,并且可以加上语音IC,来发音-IR LAMP
VB-Mscomm-rx-and-tx
- 在VB环境下利用Mscomm控件，向单片机发送数据（每按一下发送按钮即向单片机发送1个字节）， 使单片机接收到该数据后，马上再将该数据发送到VB当中。-In the VB environment using Mscomm control, sending data to the MCU (each click on the Send button to send a byte immediately SCM), SCM received the data so that immediatel
RX-TX-Remote
- MCS51 TX and RX remote for Mitsubishi and NEC format
EUSART-RX
- EUSART RX 程序，数码管显示其通信状态-The EUSART RX program, the digital display communication status
RX-Training
- 瑞萨RX系列单片机内部资源介绍及其应用领域-Renesas RX MCU internal resources to introduce its applications
msp430g2553-nrf2401-TX-and-RX-ok
- msp430g2553 nrf2401 无线通信程序-msp430g2553 nrf2401 TX and RX ok
RX系类URL认证代码
- 基于瑞萨MCU的RX系类在通过URL或者ICE认证时，需要检测的功能和逻辑完全匹配MCU的内部资源；已通过国际认证，直接可以使用。