搜索资源列表
baud
- vhdl 很好用于串行通信. 三个模快,发生时钟,发送和 接收过程-VHDL good for serial communication. Three die fast, occurred clock, sending and receiving process
FPGAprogram3
- 波特率发生器的设计，这里是实现上述功能的VHDL源程序，供大家学习和讨论。 -baud rate generator design, here is the realization of the above-mentioned functional VHDL source code for all learning and discussion.
sericommu
- 串口通信程序.在波特率为9600的串口通信程序-serial communication program. The baud rate for the 9600 serial communication program
UART_ise7_bak
- 用FPGA 实现全双工异步串口（UART），与PC 机通信。1 位起始位；8 位数据位；一个停止位；无校验位；波特率为2400、4800、9600、11520 任选或可变（可用按键控制波特率模式）。-using FPGA full-duplex asynchronous serial port (UART), and PC communication. An initiation; 8 data spaces; One-stop; No Parity; Baud Rate for 2400,48
multi_fre_timesim
- 采样时钟程序:在波特率为9600的采样时钟程序-multifrequency program. The baud rate for the 9600 multifrequency program
uart.rar
- 带自适应波特率发生器UART实现，经过FPGA验证的！,UART baud rate generator with adaptive realization, after FPGA validation!
rs232
- 完整的RS232 Verilog源代码，支持波特率可调，支持调试命令，配合串口调试工具，可作为FPGA开发中的调试平台。-Full RS232 Verilog source code, support for baud rate is adjustable to support debugging command, with the serial debugging tools can be used as the debugging FPGA development platform.
rs232
- 基于QuartusII的RS232的串口编程实验，包括有波特率的改变-Based on the RS232 serial port programming QuartusII experiments, including the baud rate change
rs232
- fpga的串口读写程序，经硬件测试成功，波特率9600.可以改变分频值适应不同的时钟和波特率-fpga serial read and write procedures, by the hardware to test the success of 9600 baud rate. frequency value can be changed to adapt to a different clock and baud rate
miniUART
- 自适应波特率的通用异步串行接口电路（ＵＡＲＴ）的ＶＨＤＬ源码，在ＡＬＴＥＲＡ上运行成功-Adaptive baud rate of the universal asynchronous serial interface circuit (UART) the VHDL source code, to run successfully in ALTERA
RS232_pro
- RS232 verilog coding 全参数化设计 可以自己设定波特率 时钟频率等 完全FPGA实现调通-RS232 verilog coding the entire parametric design can set the baud rate clock frequency of FPGA to achieve complete transfer pass
top
- RS232串行通信，采用VHDL编程，由波特率发生器，接收器和发送器构成-RS232 serial communication using VHDL programming, by the baud rate generator, receiver and transmitter constitute
UART_SUCCESS
- 实现FPGA和上位机的串口通信，里面由波特率发生器，移位寄存器，计数器，detecter,switch,switch_bus等功能块综合而成。-FPGA implementation and the host computer' s serial communication, which by the baud rate generator, shift register, counters, detecter, switch, switch_bus such as function bl
87361001Uart2
- VHDL语言编写的UART串口通讯,2400Hz的波特率时钟-VHDL language UART serial communication, 2400Hz clock of baud rate
s7enable_send0x55_UART_9600
- 最简单的UART发送程序，vhdl编写，系统时钟40M，波特率9600，外Load有效（一个高脉冲）即向PC发送一个字节0X-UART to send the simplest procedures, vhdl prepared, the system clock 40M, baud rate 9600, outside the Load effective (a high-pulse) to the PC sends a byte 0X55
uart_tx_rx
- 该工程用verilog编写，已通过串口调试助手调试通过，接收模块采用8倍波特率采样数据，有较好的滤波功能，在PC上完成自发自收功能。-Verilog prepared by the project, has passed through the serial debug debugging assistant, receiving 8 times the baud rate module sampling data, a better filtering in the PC to complet
recuart_50m
- 串口发送: 使用串口发送程序接收二进制码（9600波特率） ，用拨码开关控制发送二进制的高四位，按板上的第二个按钮，LED灯会相应的亮起，PC 会收到相应的数据-Serial port to send: Use the serial port to send a program to receive a binary code (9600 baud), with DIP switch control to send binary high-4, according to board the
senduard_50m
- 串口发送: 使用串口发送程序接收二进制码（9600波特率） ，用拨码开关控制发送二进制的高四位，按板上的第二个按钮，LED灯会相应的亮起，PC 会收到相应的数据-Serial port to send: Use the serial port to send a program to receive a binary code (9600 baud), with DIP switch control to send binary high-4, according to board the
sim_uart
- uart 收发器 verilog 代码，实现自收发功能 sys clk = 25m, baud 9600 停止位1， 无校验位； 代码实现了串口自收发功能，及把从 PC 收到的内容都发送会 PC, 其他波特率，自行修改代码即可，在 alter 的FPGA 上调试通过； -verilog code uart transceiver to achieve self-transceiver function sys clk = 25m, baud 9600 1 stop bit, no par
uart
- 一个简单的UART程序，包括接收，发送，波特率产生-A simple UART program, including receiving, sending, baud rate generation