搜索资源列表
yzl
- 这是一个圆周率计算源码,可以作为初级入门学习之用.-This is a calculated pi source can be used as the primary portal learning.
sipangzi
- 用monte carlo 方法计算圆周率pi,采用的是随机投点法。以及另一个应用程序-with monte carlo methods calculated pi pi, the vote is random point method. And another application
Batterycharger
- 高功率充电机控制程序设计。将输入指令和反馈进行比较,然后进行PI运算,再乘上单位的正弦值就变成输入电流需要跟踪的对象,然后将输入电流采样后和它进行滞回比较,比较后就可以给出开关管的开关信号了-high-power charger design control procedures. Importation of instructions and feedback, then PI operation, multiplied by the flat on the value becomes sin
afGHZpY7
- 异步电机矢量控制程序,包括坐标变换,电流采样,pi调节等功能,用的是汇编语言
pi
- 计算圆周率π,用asm汇编,速度还算可以。
SPI_master
- pic18f的spi主机代码pi c18f的spi主机代码
301
- 测温的PI程序,汇编语言编写的,主程序文件,很清晰易懂!-The PI measurement procedures, the compilation of languages, the main program file, it is clear and understandable!
car
- 使用说明 使用时打开此例题目录下pic中的图片,然后依次单击按钮“转”、“1”、“2”、“3”、“4”和“5”,就可以实现精确的车牌定位。 具体步骤 1.24位真彩色->256色灰度图。 2.预处理:中值滤波。 3.二值化:用一个初始阈值T对图像A进行二值化得到二值化图像B。 初始阈值T的确定方法是:选择阈值T=Gmax-(Gmax-Gmin)/3,Gmax和Gmin分别是最高、最低灰度值。 该阈值对不
24C01
- 读写24C01。PI C写 读写24C01。PI C写-读写24C01。PI C写读写24C01。PI C写
pi-asm
- 罗云彬的圆周率汇编源码,内含输入、输出两个子程序。-Luo Yunbin pi assembly source code, containing the input and output two subroutines.
9
- 二阶系统控制的编程设计 用积分分离pi算法 实现对电压的控制 输入电压-5.000至+5.000 需要硬件支持 -Two order control system programming design for integral separation PI algorithmTo achieve voltage control input voltage- 5 to+ 5
prime
- 并行程序设计课程上提供的计算圆周率的串行程序-The calculated pi serial program parallel programming courses
PCM
- PCM系统仿真均匀量化(必做) 1) 产生一个周期的正弦波x(t) = cos (2 * pi *t ),以1000Hz频率进行采样,并进行8级均匀量化,用 plot函数在同一张图上绘出原信号和量化后的信号。(保存为图2-1)-PCM system simulation
The-longest-Masuga-Ko-sequence
- ∏={8,7,4,2,5,1,9,3,10,6} f(j)以第j个元素Pi(j)为最后一个元素的最长增长子序列的长度。 f(j) = max{f(i)+1, 1}, a[i]<a[j], 0<i<j -Π = {8,7,4,2,5,1,9,3,10,6} f (j) to the j-th element Pi (j) is the last element of the longest length of the growth promoter
pi
- 一个简单求π的程序,精确小数点后10位,通过修改能精确更多位。-A simple procedure seeking π, accurate to 10 decimal places, more bits by modifying accurately.
pi
- 该段代码主要用于LCD检测,验证其是否损坏。主要适用单片机16F8-This code is mainly used for LCD inspection, verify that it is damaged. Mainly suitable microcontroller 16F877
pi
- 用fortran程序写代码,求pi,保留小数点后1000位-Seeking pi, retained after the decimal point 1000
the-problems-of-0-1-package
- 0-1背包问题在0 / 1背包问题中,需对容量为c 的背包进行装载。从n 个物品中选取装入背包的物品,每件物品i 的重量为wi ,价值为pi 。对于可行的背包装载,背包中物品的总重量不能超过背包的容量,最佳装载是指所装入的物品价值最高-the problems of 0-1 package
1
- 取圆周率为3.1415926,分别输入半径为40和928.335,求圆面积,要求各数据按域宽10位输出,先输出圆周率和半径,再输出其面积-3.1415926 circumference was taken, and receives a radius of 40 and 928.335, of circular area, requiring the data output by the field width 10, the first output pi and the radius, an
PMSMKG
- 永磁同步电机的Fuzzy-PI复合控制,在常规模糊控制器的基础上作出改进,对量化因子进行自整定,实现两种控制器的软切换,实现电机的高精度控制-Fuzzy-PI complex control of permanent magnet synchronous motor, made on the basis of conventional fuzzy controller based on the improvement of quantitative factors auto-tuning, so