搜索资源列表
gy
- 安徽省电力公司电子式多功能电能表通信规约 -Power companies in Anhui Province Multi-function Electronic Energy Meter Communication Protocol
GY-26
- GY-26电子指南针的测试程序,用液晶显示当前的角度,以及磁偏角等信息-GY-26 electronic compass test procedures, the use of liquid crystal display the current angles, and CiPianJiao and other information
dianzizhinanzheng
- GY-26电子指南针资料、源码等(温度+IIC+串口)-GY-26 electronic compass data, source, etc. (temperature+ IIC+ serial)
The-GY-29-MCU-IIC
- GY-29与单片机IIC通信程序实例 已通过-The GY-29 MCU IIC communication program
GY-85_IMU
- 9自由度IMU模組 GY-85 (ITG3205/ITG3200+ADXL345+HMC5883L) 控制範例源代碼-9 degrees of freedom IMU modules GY-85 (ITG3205/ITG3200+ADXL345+HMC5883L) control sample source code
GY-29-ADXL345-IIC-testing-procedures
- GY-29 ADXL345 IIC测试程序-GY-29 ADXL345 IIC testing procedures
The-GY-52-three-axis-gyroscope-
- 三轴陀螺资料,里面含有例程及代码,在51/STM上和Arduino运行完美。-The GY-52 three axis gyroscope to send data.
GY-87_STM32
- 是GY-87模块的stm32测试程序,串口输出温度压强 陀螺仪 加速度 温度 指南针的数据-GY-87 module the stm32 test procedures, data serial output temperature and pressure gyroscope acceleration temperature compass
GY-30
- 照度传感器GY-30,测量光照强度C程序源码-Illumination sensor measures the light intensity C program source code
GY-80-ARDUINO
- GY-80-ARDUINO,GY_80九轴BMP085,基于ARDUINO,实现对ADXL345 ,BMP085,HMC5883L,L3G4200D的操作-GY-80-Arduino, nine GY_80 axis BMP085 based on Arduino, ADXL345, BMP085, HMC5883L, L3G4200D operation
GY-61-ADXL335
- GY-61 ADXL335 的程序代码,需要的可下一下-The source code of GY-61 ADXL335
GY-30
- 光感測器gy-30,感測光強度的C語言程式碼,GY-30採用I2C的通訊協定來收發,由8051的P2_2與P2_3分別為SCL & SDA,輸出端為P1。
STC-GY-31
- 基于STC51单片机和GY-31颜色识别模块的程序,带白平衡校准。通过LCD1602显示RGB-The code can recognize the color.It depends on the 51 MCU
GY-65
- 基于51单片机的GY-65气压传感器模块串口通信,液晶显示源程序及模块引脚接线图-Display based on 51 microcontroller GY-65 pressure sensor module serial communication, LCD source code and module pin wiring diagram
GY-88_51
- 基于51单片机的GY-88数字陀螺仪传感器模块通信程序-Based on 51 SCM GY-88 digital gyroscope sensor module communication program
GY-88_stm32
- 基于STM32芯片的GY-88数字陀螺仪传感器模块通信程序-Based STM32 chip GY-88 digital gyroscope sensor module communication program
GY-80_STM32
- 基于STM32芯片的GY-80九轴数字陀螺仪及气压传感器模块串口通信程序-Based STM32 chip GY-80 nine-axis digital gyroscope and pressure sensor module serial communication program
CC2530-read-GY-30-show-in-LED
- 使用CC2530通过I2C读取光敏传感器的数据并显示在LCD上,输出直接为光照值,数字光强度检测模块:GY-30电压范围3-5v光照度范围:0-65535 lx-The use of CC2530 to read through a photosensitive sensor I2C data in the LCD display, the output directly to the illumination value, light intensity detection module of
GY-85-arduino-master-new
- 这是一个通过用arduino控制GY-85九轴陀螺仪的例程,包括收集gy85传感器发回来的数据,以及将它们打印出来(This is an example to control GY-85 by using arduino)
GY-271-HMC5883 STC IIC测试程序
- 单片机STC89C51与使用HMC5883的GY-271进行IIC通信的示例代码(Sample code for IIC communication between MCU STC89C51 and GY-271 using HMC5883)