CDN加速镜像 | 设为首页 | 加入收藏夹
当前位置: 首页 资源下载 源码下载 数值算法/人工智能 仿真建模 搜索资源 - AT

搜索资源列表

  1. yibumotor_DTC_control

    2下载:
  2. 异步电机直接转矩控制系统仿真: 模型整体结构分为三大部分:主电路部分(直流电源、逆变器、电机)、控制系统部分(采用的是直接转矩控制,所以主要有坐标变换模块,灰色部分,磁链观测器模块,红色部分,直接转矩开关表选择模块,蓝色部分,以及外环的转速调节器ASR)剩下的就是仿真结果波形观测部分(观测信号依次向下为定子ab相线电压、三相定子电流、电机转速、电机电磁转矩) 运行初始条件为以1420r./min的额定转速电机空载启动,在0.3s时刻突加额定负载50牛米。在0.5s时刻电机转速突然下降为120
  3. 所属分类:仿真建模

    • 发布日期:2017-12-27
    • 文件大小:30kb
    • 提供者:rogermilk
  1. 夜间车牌识别程序

    0下载:
  2. 应用MATLAB进行仿真模拟,设计的夜间车牌识别程序,能够实现黑暗空间内的汽车车牌的识别、读数。(The application of MATLAB to simulate and design the license plate recognition program at night can realize the recognition and reading of car license plate in the dark space.)
  3. 所属分类:仿真建模

    • 发布日期:2018-04-20
    • 文件大小:34kb
    • 提供者:ljing724
  1. ant

    0下载:
  2. 此程序是用元胞自动机来仿真模拟蚂蚁游戏。初始时,蚂蚁位于一张空白画布的某个方格里。如果当前蚂蚁在白色方格上,则对当前方格反色,左转?90?度,前进一格;如果当前蚂蚁在黑色方格上,则对当前方格反色,右转?90?度,前进一格。如此反复。(This program is using cellular automata to simulate the ant game. At the beginning, the ant is in a grid of a blank canvas. If the cu
  3. 所属分类:仿真建模

    • 发布日期:2018-05-01
    • 文件大小:5kb
    • 提供者:慕一一
  1. 模拟薄膜生长的 kmc 程序源码 动力学蒙特卡洛

    2下载:
  2. Arizona State University大学Adams, James教授课题组的KLMC程序,模拟cu100晶面上薄膜生长的kmc程序源码.AWL is the Kinetic Lattice Monte Carlo code for simulating thin film growth, which is developed by Zhiyong Wang, Youhong Li and James B. Adams at Arizona State University. AWL
  3. 所属分类:仿真建模

  1. me

    6下载:
  2. 风电齿轮的动力学建模程序,模拟了齿轮振动处的信号(The dynamic modeling program of wind turbine gears simulates the signals at the vibration of gears.)
  3. 所属分类:仿真建模

    • 发布日期:2020-06-19
    • 文件大小:1kb
    • 提供者:JM_Ron
  1. wave simulation

    2下载:
  2. 通过频谱来模拟波浪,程序为Jonswap谱的波浪模拟,可随意调整谱参数、时间间隔和模拟的时间长度(The wave is simulated by the spectrum, and the program is a wave simulation of the Jonswap spectrum. The spectral parameters, time interval and length of the simulation can be adjusted at will.)
  3. 所属分类:仿真建模

    • 发布日期:2020-12-22
    • 文件大小:1kb
    • 提供者:zhangmeng1994
  1. 转子系统启动时的瞬态动力学分析

    3下载:
  2. 转子系统启动时的瞬态动力学分析,有限元分析(Transient Dynamics Analysis of Rotor System at Start-up)
  3. 所属分类:仿真建模

    • 发布日期:2020-12-02
    • 文件大小:1kb
    • 提供者:健康一生
  1. 第十次作业

    1下载:
  2. 一受均匀拉力的板,中心带贯穿裂纹,裂纹长2a,使用4节点单元计算裂尖应力分布和应力强度因子(A uniform tensile plate with a through crack in the center and a crack length of 2a is used to calculate the stress distribution and stress intensity factor at the crack tip using a four node element)
  3. 所属分类:仿真建模

    • 发布日期:2020-08-23
    • 文件大小:1kb
    • 提供者:Thcffy
  1. DSIP

    2下载:
  2. abaqus子程序disp,可以实现不同时间不同的位移(The ABAQUS subroutine disp can realize different displacements at different times)
  3. 所属分类:仿真建模

    • 发布日期:2021-03-24
    • 文件大小:5kb
    • 提供者:victor009
搜珍网 www.dssz.com